4 guidelines for re-masking a bike seat like a pro

The tough-and-tumble ailment of my Honda XR250 has been its ideal function in excess of the past calendar year. The mismatched and broken plastics merged with the torn, duct-taped seat meant that I only experienced pleasurable riding the factor. If I or a pal dropped the bicycle on the trail, no 1 desired to sense the least little bit of guilt. There were being a lot of motor vehicles in my garage with awesome paint and meticulously preserved finishes, but this XR wasn’t a person of them. That is all starting up to modify, however.



a close up of a sign


© Delivered by Hagerty


I’ve torn this equipment all the way down to its skeleton, and I’m thoroughly rebuilding it to function flawlessly but nonetheless be truly usable. 1 product that would not go muster was that duct-taped seat. Even when I tried to dismiss it, that tear bothered me. It wasn’t merely an aesthetic issue, both, since the rip was enabling the foam foundation beneath it to deteriorate. The seat necessary a new go over.

Re-masking a seat is not a massive offer, assuming you know a couple very simple tricks. In this article are the four key kinds.

Acquire the greatest high quality protect you can



text: Kyle Smith


© Provided by Hagerty
Kyle Smith


 

Many vehicle- and bicycle-relevant factors have dropped in output top quality recently, but alternative seat covers for motorcycles have endured significantly terribly. The race to produce the most affordable address has manufactured it challenging to come across a person really worth your coin. The hues and markings almost never match OE-spec, even if you are prepared to expand your look for to any and all products. If you can get a seat deal with of fantastic excellent, do not be low-priced. The match and complete is really worth the funds, and it will also very likely be easier to operate with as you put in it.

Splurge for an electric or pneumatic stapler



a knife sitting on top of a wooden cutting board: Kyle Smith


© Delivered by Hagerty
Kyle Smith

Alongside the similar strains of argument, shell out a several bucks and get oneself an electric powered or pneumatic stapler. In this situation, I took a trip to Harbor Freight and acquired the extensive-crown pneumatic stapler. It is just about $30 and will perfectly provide my desires. Changing a seat go over with the ideal instruments will still make you want for a 3rd hand, but the means to accurately and swiftly area a staple will make the completed final result appear significantly cleaner.

Really don’t be frightened of the heat



Kyle Smith


© Furnished by Hagerty
Kyle Smith

My workspace is heated, but I preserve it at just 50 levels for most of the cold Michigan winter. That is not virtually worm enough to allow the vinyl go over to extend thoroughly. In a excellent world I would lay out the deal with in the heat sun for the early morning even though I disassemble the seat, and it would be wonderful and versatile by the afternoon. For this late-January venture, the electrical heat gun obtained pressed into assistance. Careful—and I suggest careful—software of heat will make fitting the new address so significantly easier. The cause you want to be additional watchful is that vinyl, and primarily inexpensive vinyl, does not give you considerably warning right before it melts and results in being pretty unsightly. Something earlier mentioned warm to the touch is hazardous, and most respectable warmth gun will warmth slim vinyl up to that point swiftly.

Head to toe, then facet to aspect



a screenshot of a cell phone: Kyle Smith


© Provided by Hagerty
Kyle Smith

For off-highway-form seats like this one, it’s best to start off with the main edge (which would sit in opposition to the gas tank). Get the content nice and centered and tack it in put with just one or two staples. Then shift to the rear of the seat, leaving the sides loose. With the cover centered and secured, commence at the front and alternate from aspect to aspect, stretching and stapling the address in spot to remove wrinkles or uncomfortable pulls. Tuck the rear corners nicely, and you are finished.

I’ve only outlined a handful of recommendations and not the whole approach, but in the slideshow beneath you can see each individual of my measures in re-masking this distinct seat. The completed product is very good but not wonderful, which indicates that it will surely suffice for the abuse the XR is probably to see this yr. I count on to exchange this go over yet again upcoming winter season, not since of inappropriate installation, but for the reason that of accumulated don and tear.



a piece of luggage: Torn XR250 seat


© Presented by Hagerty
Torn XR250 seat



Torn XR250 seat 2


© Offered by Hagerty
Torn XR250 seat 2



disassembling xr250 seat


© Supplied by Hagerty
disassembling xr250 seat



pulling old staples from XR250 seat pan


© Delivered by Hagerty
pulling previous staples from XR250 seat pan



cleaning XR250 seat pan


© Offered by Hagerty
cleaning XR250 seat pan



old staples from XR250 seat


© Offered by Hagerty
previous staples from XR250 seat



a hand holding a banana: XR250 seat foam tear


© Supplied by Hagerty
XR250 seat foam tear



a sign on a table: XR250 seat foam


© Offered by Hagerty
XR250 seat foam



text: fitting cover on XR250 seat


© Offered by Hagerty
fitting protect on XR250 seat



heat gun Xr250 seat


© Provided by Hagerty
warmth gun Xr250 seat



a wooden table: Finished XR250 seat nose


© Delivered by Hagerty
Concluded XR250 seat nose



an orange sign that is on a table: finished XR250 seat


© Offered by Hagerty
finished XR250 seat


 

The submit 4 ideas for re-covering a motorcycle seat like a professional appeared first on Hagerty Media.

Continue on Looking at

Share This Post